NOTE — Considering operational problems, maxi- mum wall thickness of pipes are considered around 63 mm. No other reworked or recycled material shall be used. Plb Hdpe Duct in Jaipur. In case of variation in water temperature, the working pressure needs to be modified as. Pipee direction of the pipe axis shall be marked on the pieces.
|Published (Last):||25 March 2012|
|PDF File Size:||1.48 Mb|
|ePub File Size:||16.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
NOTE — Considering operational problems, maxi- mum wall thickness of pipes are considered around 63 mm. No other reworked or recycled material shall be used.
Plb Hdpe Duct in Jaipur. In case of variation in water temperature, the working pressure needs to be modified as. Pipee direction of the pipe axis shall be marked on the pieces. The manufacturer or the supplier may be asked iis improve the design and resubmit the product for type approval.
Call Send a quick message. Singh Members Shri V. If in repeat test, no single failure occurs, the type of pipe under consideration shall be considered eligible for type approval.
Legal Status hxpe Firm Private Ltd. However, occasional rise piprs temperature as in summer season with concurrent corresponding reduction in temperature during night has no deleterious effects on the life and working pressure of the pipes. If any of the samples fails in the repeat tests, the typeof pipe shall not be approved. Shenbagawandam Alternate Shri S. The material of the stripes shall be of the same type of resin, as used in the base compound for the pipe.
We offer them in different sizes and diameters and are valued for optimum performance and easy installation. For ascertaining conformity of the lot to the require- ments of this specification, samples shall be selected in accordance with the provisions as men- tioned under 9.
Measure the minimum distance between the two marks. IS high density polyethylene pipes for potable water supplies Find more suppliers in Mumbai Hdpe Tube in Mumbai. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2: The test pieces shall not touch each other.
The lot shall be deemed not to have met these requirements if the number of defectives found in the first sample is greater than or equal to the corresponding rejection numbers given in col 6 of Table 7. Regarding guidance for laying and jointing of polyethylene pipe, including storage and handling, a reference may be made to IS Part Hdpe Corrugated Subsoil Drainage Pipe.
Sharma Alternate Shri O. View Contact Call Seller Now. A mark shall be scribed on os external surface approximately 50 mm from each end of the test pieces in the axial direction of pipe, in the case of complete section of pipe, the mark shall be scribed around the whole circumference.
Shembekar Alternate Dr Y. The wall thickness shall be measured by a dial vernier ia ball ended micrometer. This does not preclude the free use, in the course of implementing the standard, of necessary details, such as symbols and sizes, type or grade designations. C-1,2 Thermometer — Graduated to 0. Page 7, clause 8. NOTES 1 The outside diameter shall be measured at a distance of at least mm from the end of the pipe. Our entire product range is well-tested.
Standards ppipes also reviewed periodically; a standard along with amendments is hdpw when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision.
Get best deals for coconut. Our Company is enjoying technological advantages with latest equipped on-site laboratory at manufacturing plant. The basis for the values specified is: These innovative facilities are in the forefront of product development, which go forward the most careful, vigilant standards of product testing based on national and international standards.
Pipes for sewer- age hdpee industrial effluents are being covered in a separate standard. TOP Related Articles.
HDPE PLB Duct Pipes and Fittings
HDPE Fittings as Per IS 4984
Is 4984 HDPE Pipes